Small Spaces cutting template
Slim Laundry Tower Cut List Template
A 24-inch-wide laundry storage tower with shallow shelves, open back rails, and appliance-service clearances. Use this as a starting point, then change every dimension for your room, hardware, material thickness, and joinery before cutting.
Small-space planning boundary
This paired project starts with three constraints that should be measured before the parts list is released.
- Measured footprint: 24 in wide × 14 in deep × approximately 72 in high outside the appliance service envelope.
- Transport constraint: The 72 × 14 in sides require a ceiling and doorway turn check; assemble in place when the finished case cannot rotate upright.
- Reversible-installation boundary: A removable anti-tip connection still requires permitted drilling, utility awareness, and clear appliance service access.
Inspect the calculated slim laundry tower example, then use Measure the laundry service zone and Diagnose lost appliance clearance before finalizing dimensions.
Plan the slim laundry tower before buying sheets
Start by confirming the finished width, depth, height, access clearances, and load requirements. This template is intentionally made from rectangular plywood parts so you can adapt it without redrawing the whole project. Keep matching pieces grouped together, mark visible faces, and leave room for edge banding, backs, doors, drawers, hinges, or trim that apply to your version.
Use 3/4 inch plywood for the structural parts unless your design calls for another thickness. A template is not a structural rating: add bracing, wall anchoring, weather protection, or a thicker panel whenever the location, load, or local requirements demand it.
Slim Laundry Tower project-specific checks
Use these checks with the sample parts list before calculating sheet count or making a purchase.
- Measure appliance doors, vibration zone, hoses, vent, valves, plugs, baseboard, and service removal path.
- Keep detergents and heavy containers in stable reachable zones and protect plywood from humidity and spills.
- Anchor the tall narrow case to verified structure without blocking required appliance or utility access.
Slim Laundry Tower parts list
Material: 3/4 in plywood
Kerf allowance: 1/8 in between cuts
Grain direction: keep visible faces consistent
Part | Size (in) | Qty
-------------------+-----------------+----
Sides | 14 x 72 | 2
Top and bottom | 13-1/4 x 24 | 2
Shelves | 13-1/4 x 22-1/2 | 4
Back rails | 4 x 24 | 3Review each part against the actual construction method before cutting. Reduce a shelf or bottom for side-panel thickness where needed, leave back-panel or drawer-slide clearance, and make a test piece for any groove, dado, or hardware opening. Label repeated parts as a batch so their orientation stays consistent.
Check the sheet layout and cut order
Place the largest parts first, then nest matching rectangles around them. Square footage alone cannot tell you the sheet count because saw kerf, grain direction, and the shape of the remaining offcuts matter. Enter this adjusted list in the plywood cut calculator with your real sheet size and blade kerf before purchasing material.
Break full sheets into manageable strips first, then crosscut the final parts. Keep pairs together, label the inside faces, and dry-fit the case on a flat surface before driving final fasteners. The cut list calculator is useful if the project also uses solid-wood rails, trim, or stretchers.
Assembly checks that prevent rework
Dry-fit the major panels, measure both diagonals for square, and confirm that moving parts or equipment have the clearance you planned. Pre-drill near plywood edges, test fasteners in an offcut, and attach the back only after the cabinet or frame is square. Read how to read a cut list and saw kerf explained if you need a refresher before finalizing the layout.
How this template was prepared
The parts list models a common slim laundry tower carcass or frame so you have named pieces and repeated quantities to review. It deliberately leaves hardware, joinery, edge treatment, structural loads, and site conditions open because those choices change final dimensions. Before cutting, verify every opening and finished dimension, confirm material thickness with a caliper, apply hardware clearances, and review the optimized layout against the drawing or room. For a transparent comparison of common template inputs, see the plywood project yield benchmark.
Make this template yours
Replace the sample slim laundry tower dimensions with the real job
The sample rows are a planning start. Create a CutList project with the measured dimensions, actual material, blade kerf, grain direction, and approved quantities before releasing parts.
- Free basic layouts
- No login
- No cloud upload
- Works offline
On a computer? Scan with your iPhone or iPad.
More project templates
Browse the full plywood cut list template library for related builds, then save a revised version in the CutList optimizer app when you want to compare sheet counts or keep the plan for later.